Go CCIE Go!! - A Cisco Certified Internetwork Expert

show interface Serial0/2/0
should there be broadcast queue drops, try increasing fr broadcast queue-limit.
-Sakthi
— Shine Joseph wrote:
> Moe, > > > > That’s good. > > > > Can you swap the DTE/DCE side and apply the clock on > FR switch rather than > on the router. See it if that makes a difference. I > strongly suspect that. > > > > Regards, > > Shine > > > > _____ > > From: cisco-addicted > [mailto:cisco.addicted@gmail.com] > Sent: Thursday, 20 March 2008 3:49 PM > To: ‘Shine Joseph’; ‘But Nicky’; ‘Rik Guyler’; > surendratk@hotmail.com; > ‘Jonathan Greenwood II’ > Cc: ‘Adel Karim’; ‘Envuladu Tsaku’; > steveaggie@gmail.com; ‘Cisco > certification’ > Subject: RE: EIGRP adjacency Flapping > > > > Dear, > > The clock rate on R2 serial because I connected the > DCE cable from R2 side > not the FRSW. Is this a problem?? Should all the > FRSW be the DCE and the > other routers be DTE?? > > > > And by the way the ping from all the three routers > on the FR interfaces > working fine, but when I tried to use the broadcast > address; only R2 was > able to ping both spokes. > > > > The good news that after configuring the neighbor > command between them, the > adjacency worked fine . But what was the cause of > the problem????? What if > they asked me not to use this command ??? > > > > With all regards > > Moe > > > > > > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! R1 > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > > > > Rack1R1#ping 183.1.123.2 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 183.1.123.2, > timeout is 2 seconds: > > !!!!! > > Success rate is 100 percent (5/5), round-trip > min/avg/max = 56/56/60 ms > > Rack1R1# > > Rack1R1# > > Rack1R1#ping 183.1.123.3 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 183.1.123.3, > timeout is 2 seconds: > > !!!!! > > Success rate is 100 percent (5/5), round-trip > min/avg/max = 112/112/112 ms > > Rack1R1# > > Rack1R1# > > Rack1R1# > > Rack1R1#ping 183.1.123.255 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 183.1.123.255, > timeout is 2 seconds: > > > > Reply to request 0 from 183.1.123.2, 84 ms > > Reply to request 1 from 183.1.123.2, 84 ms > > Reply to request 2 from 183.1.123.2, 84 ms > > Reply to request 3 from 183.1.123.2, 84 ms > > Reply to request 4 from 183.1.123.2, 84 ms > > Rack1R1# > > Rack1R1# > > > > > > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!1 R2 > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > > > > > > Rack1R2# > > Rack1R2#ping 183.1.123.1 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 183.1.123.1, > timeout is 2 seconds: > > !!!!! > > Success rate is 100 percent (5/5), round-trip > min/avg/max = 56/56/60 ms > > Rack1R2# > > Rack1R2# > > Rack1R2#ping 183.1.123.3 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 183.1.123.3, > timeout is 2 seconds: > > !!!!! > > Success rate is 100 percent (5/5), round-trip > min/avg/max = 56/56/56 ms > > Rack1R2# > > Rack1R2# > > Rack1R2# > > Rack1R2#ping 183.1.123.255 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 183.1.123.255, > timeout is 2 seconds: > > > > Reply to request 0 from 183.1.123.3, 128 ms > === message truncated ===